Proceedings of the World Engineering Congress VOLUME III
Engineering Science Part 1 (Section II of Congress)
Contents
1. Deflections and Stresses in Pipe Bends(No.317):BY W.HOVGAARD,PROF.(U.S.A.) / 1
2. Strength of Cast Iron under Bending and Compression(No.400):BY T.MATSUMURA,KH.,PROF.,B.FUJIMOTO(JAPAN) / 31
3. The Effects of an Axial Groove on the Torsional Elasticity of a Round Bar(No.462):BY T.NISHIHARA,PROF.(JAPAN) / 45
4. A Method of Measuring Fatigue Degree and Its Recovery(No.361):BY Y.ASAKAWA(JAPAN) / 63
5. The Imperfect Strut and the Arch(No.158):BY R.W.H.HAWKEN(AUSTRALIA) / 73
6. Deflections‐Statical and Dynamical(No.159):BY S.I.BACKSTROM(AUSTRALIA) / 115
7. Springs and Spring Materials(No.226):BY R.G.BATSON,G.A.HANKINS,D.SC.(G.B.) / 201
Discussion / 220
8. A Method of Approximate Solution analogous to Ritz's in the Problems of Elasticity(No.84):BY K.OKUDA(JAPAN) / 221
9. On the Yield Point of Mild Steel(No.107):BY F.NAKANISHI(JAPAN) / 235
Discussion / 260
10. Practical Determination of the Elastic Limit(No.791):BY T.INOKUTY,KH.,PROF.(JAPAN) / 263
11. Photo‐Elasticity‐Introduction of a New Material and Photographic Method(No.357):BY Z.TUZI,KH.(JAPAN) / 267
12. On the Process of the Failure of Metals under Stress(No.593):BY K.YUASA(JAPAN) / 315
13. New Formulas for Helical Springs(No.150):BY K.T.WANG(CHINA) / 349
14. New Graphic Methods of Finding the Area of Irregular Figures(No.151):BY K.T.WANG(CHINA) / 363
15. Effects of Circular Holes and Notches on Stress‐Distribution in Simple Beams of Short Spans(No.100):BY T.FUKUHARA,PROF.(JAPAN) / 371
16. An Experimental Study of the Forced Vibration of Beam under Moving Load(With Special Reference to"Zimmermann's Effect")(No.96):BY H.SHIBATA(JAPAN) / 395
17. De l'Orientation des Axes Electriques du Quartz a l'Aide des Figures de Corrosion(No.598):BY A.DE GRAMONT,DR.SC.(FRANCE) / 417
Discussion / 421
18. An Investigation of Abrasion in Cements and Mortars(No.90):BY S.UCHIDA(JAPAN) / 423
19. Properties of Materials at High Temperatures(No.227):BY R.G.BATSON(G.B.) / 441
20. The Plastic and Viscous Deformation of Metals and the Effect of Time on the Breaking Strength at Ordinary and High Temperatures(No.228):BY F.C.LEA,PROF.,D.SC.(G.B.) / 457
21. Fatigue of Metals under Repeated Stress(No.640):BY A.ONO,KH.,PROF.(JAPAN) / 477
22. A Rapid Method of Determining Endurance Limit by Means of Measuring Electrical Resistance in Heat‐treated Steel(No.86):BY S.IKEDA(JAPAN) / 491
23. Experiments in Observing Longitudinal and Lateral Strains of Concrete under Statical and Repeated Compressive Loads(Determination of Poisson's Ratio of Concrete).Some Notes on Elastic Properties of Concrete(No.98):BY H.YOSHIDA,PROF.(JAPAN) / 521
24. A Supplementary Note on the Effect of the Steady Twist upon the Safe Limiting Range of Repeated Bending Stresses(No.66):BY R.MIYASIMA(JAPAN) / 539
25. Some Points in Connection with the Failure of Metals under Repeated Stresses(No.229):BY F.C.LEA,D.SC.,PROF.(G.B.) / 541
26. Latest Researches on Metallic Materials' Resilience Made in the Railway Experimental Institute of the Communications(Italian State Railways)(No.520):BY P.FORCELLA,DOTT.CAV.(ITALY) / 553
27. Some Important Results of Repeated Violent Blows by Alternate Flexion on Cut Bars(No.521):BY P.FORCELLA,DOTT.CAV.(ITALY) / 583
「国立国会図書館デジタルコレクション」より
書名
World Engineering Congress, Tokyo 1929 = 萬國工業會議 : proceedings